manuals/manuals_Support_Center_manuals_Titanium2_20PM0350_01

Megatouch™ Titanium 2 Edition

QTY

PART NUMBER

DESCRIPTION

PA0037-03

MEGATOUCH TITANIUM 2 CD #1

PA0037-04

MEGATOUCH TITANIUM 2 CD #2

SA3052-XX or
SA3053-XX

TITANIUM KEY or
TITANIUM CHAMPIONSHIP KEY

EC2179-01

CENTRONIC IDE-POWER RIBBON CABLE

GL3100-30

COUNTERTOP TITANIUM 2 SIDE DECAL, L

GL3100-31

COUNTERTOP TITANIUM 2 SIDE DECAL, R

Megatouch™ XL Titanium 2 Hardware Requirements

In order to successfully upgrade your unit, your Megatouch™ XL game must be currently

running the Megatouch™ XL Gold, Platinum, or Double Platinum software on a hard drive.

In order to check the program running on your game, push the set-up button inside the

cabinet. The program information will be displayed in the upper left corner of the first

screen that appears. If you are running Gold software, the program number will be

PG3001-03-XX, or PG3001-04-XX. If you are running Platinum software, the program

number will be PG3004-01-XX.

CAUTION:

Before performing any upgrade, it is important to remove any static electricity

from your body. To remove static electricity from your body, ground yourself by touching a

grounded piece of metal on the game before handling any boards, chips, connectors, etc.

Failure to ground yourself before performing an upgrade may result in damage to your

system and may prevent you from performing the upgrade.

*The installation of this kit requires a CD-ROM drive which is not included.

It is recommended

that you use a CD-ROM drive of at least 8X or better that is capable of operating on an angled
surface, as you may not always have a level surface on which to place the drive.
You must configure your CD-ROM drive as the

Master Drive

CONTENTS:

Connecting a CD-ROM Drive

Turn off power to the game.

Unlock and open the CPU section door

to access the PC tray.

Connect the 2 x 20-pin IDE connector

(see Figure 1) to the IDE interface con-

nector on the CD-ROM drive. Make sure

the red stripe on the ribbon cable

matches up with pin 1 on the IDE inter-

face connector (see Figure 2).

Connect the four (4) pin power con-

nector on the ribbon cable (see Figure

1) to the DC power input on the CD-

ROM drive (see Figure 2).

Make sure that your CD-ROM drive is

set to MASTER. See Figure 2 for typi-

cal Master/Slave drive location.

Locate the centronics connector.

Countertop: The centronics connector

is located on top of the motherboard

display frame (see Figure 3).

Upright: The centronics connector is

located on the PC shelf (see Figure 4).

PM0350-01 MEGATOUCH™ TITANIUM 2 EDITION KIT 1

Connect the centronics connector on

the ribbon cable to the centronics con-

nector on the game.

NOTE: When positioning your CD-ROM
drive, it is important that you find a suitable
place where the CD-ROM drive will not be
in danger of coming in contact with any com-
ponents or wires inside of the game.

Program Installation

NOTE:

Performing this upgrade will delete

previous information and files on your hard
drive. If you want to retain any pertinent
information (ex: Books Screen information),
you will need to document that information
before performing the upgrade.

The update process could take anywhere
from 10 to 15 minutes, depending on the

speed of your CD-ROM drive.

Turn on the game.

Make sure all DIP switches on DS2 and

DS3 are set to the OFF position.

10. Insert the CD labeled Disc 1 into the

CD-ROM drive.

11.

Turn off the game and turn it back on.

12. If you have an ELO touchscreen, you

will be asked to perform a touchscreen

calibration. Follow all directions on the

screen.

13. The message “

Select A Language”

will appear on the screen. After you

select a language, the message:

“By

continuing with this installation

program, you indicate that you

accept the terms of Merit’s soft-

ware license agreement.” The soft-

ware license agreement is found on

page 5 of this manual. If you accept

the terms, select

“Continue Install”. If

you do not accept the terms, select

“Cancel Install” and remove the CD.

NOTE: If you select “Cancel Install,” your
game will abort the update and reboot in its
current version.

14. When the first CD is finished installing,

the message:

“Please replace the current CD

with CD #2 then touch screen to

continue” will appear on the screen.

Insert the CD labeled Disc 2 and touch

the screen.

15. After the update is complete, you will

see a screen that says:

“Upgrade Successful Please Re-

move CD and Reboot.”

16. Remove the CD and turn off power to

the game.

17. Carefully disconnect the ribbon cable

from the centronics connector on the

game.

NOTE: When disconnecting the ribbon
cable, carefully disconnect the cable by
grasping the connector and not the cable
itself.

18. After performing the upgrade you must

calibrate the touchscreen by pressing

the “Calibrate” button inside the game

and following the instructions on the

screen.

Security Key Installation

19. Locate the security key (the button-

shaped disc with the spoon handle)

on the button key adapter board on the

I/O board of the motherboard assem-

bly.

Countertop: See Figure 3.

Upright: See Figure 4.

20. Remove the existing security key from

the adapter board and replace it with

the security key supplied in this kit.

21. Close and lock the CPU section door.

22. Turn on power to the game and enjoy

the Titanium 2 Edition program.

2 MEGATOUCH™ TITANIUM 2 EDITION KIT PM0350-01

Remove the existing side decals. (Remove any remaining adhesive residue with an

adhesive remover.)

NOTE: Make sure not to get any adhesive removing solvents or solutions on the
touchscreen, as they may damage the touchscreen.

When you are finished removing any excess adhesive from the game, wipe the sur-

faces with alcohol solvent. The surfaces must be clean and free from dirt for the new

decals to adhere properly.

Partially peel the backing from the top edge of the provided decal. Center the decal on

the side of the game and apply the decal, leaving a half inch around the outside of the

decal that will not be covered. Repeat the same step for the other side of the game.

Installing the Side Decals on a Countertop game

4 MEGATOUCH™ TITANIUM 2 EDITION KIT PM0350-01

Megatouch™ XL Titanim 2 Championship Edition
Instructions (For Championship Kits Only)

Overview

The Titanium 2 Championship Edition™ is a completely programmable tournament pro-

motion system, allowing players to compete for a prize pool based on the income from

premium-priced tournament games. The top three scorers, at the completion of a tourna-

ment, are entered into the Winners’ List for retention until they claim their prizes. The game

can be set to use cash prizes or redemption points depending on local laws.

Up to four tournaments can be programmed to run simultaneously. The settings for

each tournament, including game cost, rounds, starting time, ending time and date, duration

and prize pool, can be independently programmed to provide maximum flexibility and promo-

tional potential. Each tournament can be further programmed to be a single, repeating

tournament game or a sequence of different games, which change for each tournament

period.

Players who achieve one of the three high scores during a tournament must enter their

name, along with their own four-digit personal identification number (PIN). Should they finish

as one of the three highest scorers in that tournament, the PIN will be used to ensure positive

identification of the player. Provided an attendant is present, prizes may be claimed anytime

after the completion of a tournament. Once the prize is awarded, it is noted on the Winners’

List and is accounted for in the bookkeeping statistics.

PM0350-01 MEGATOUCH™ TITANIUM 2 EDITION KIT 5

Programming a Tournament

Press the SETUP button (located be-

hind the cashbox in countertop models

and on the PC shelf in upright models).

At the Setup Screen, touch the SYS-

TEM SETTINGS icon.

At the System Settings Screen, touch

the TOURNAMENT icon. This will take

you to the Tournament Controls screen

(see Figure 5). At this screen, touch

the SET-UP icon to enter the Tourna-

ment Clock/Currency Screen.

At the Clock/Currency Screen (see Fig-

ure 6) confirm the correct date and

time (if the date and/or time is incor-

rect, set the correct values using the

UP and DOWN arrows

next to each

field). Set the credit value by touching

the UP and DOWN arrows until the de-

sired value is shown. Set the appro-

priate currency type by touching the

desired currency symbol at the bottom

of the screen.

(NOTE: THE CREDIT VALUE IS
LOCKED AND CANNOT BE CHANGED
WHILE A TOURNAMENT IS RUNNING!)

Touch the “Next Page” icon to enter

the Tournament Setup Screen (see Fig-

ure 7).

FIGURE 5 - TOURNAMENT CONTROLS

SCREEN

B U T T O N

I C O N

D E S C R I P T I O N

S E T - U P

A c c e s s e s t h e T o u r n a m e n t
S e t - U p s c r e e n s .

C L E A R

W I N N E R S

E n t e r s   t h e   C le a r   W in n e r s
s c r e e n ,   w h ic h   a llo w s
y o u   t o   c le a r   a ll  w in n e r s   o r
c le a r   a ll  w in n e r s   w h o
h a v e   b e e n   a w a r d e d   p r iz e s .

R E S E T

A L L

E r a s e s   A L L   t o u r n a m e n t
in f o r m a t io n   f r o m
t h e   m e m o r y   o f   g a m e !
T h is   in c lu d e s   A L L   p r iz e
in f o r m a t io n !

FIGURE 6- CLOCK/CURRENCY SCREEN

6 MEGATOUCH™ TITANIUM 2 EDITION KIT PM0350-01

FIGURE 7 - TOURNAMENT SETUP SCREEN

(EXPLANATION OF BUTTONS CONTINUES ON FOLLOWING PAGE)

Tournament

Sequence

A programmed sequence of up to 4 tournament
games. Touch a Tournament Sequence # to
program the desired tournament sequence (each
tournament sequence is programmed independently).

Tournament

Game

Sequence

To enter a game into the tournament game sequence,
touch the desired tournament game sequence field
and then touch the game name in the tournament
game list. Select the REPEAT icon to have the
programmed games repeat their sequence; select the
END icon to have the tournament games end after the
programmed sequence.

Tournament

Cost Fields

Touch an individual game to change the tournament
game cost. Use the up and down arrows to view all
available tournament games.

Tournament

Rounds Field

Touch the tournament round number to toggle the
number of rounds for the associated game. Game
rounds can be set from as low as 1 to as high as the
default number of rounds.

Reset Defaults

Touch to reset the default tournament settings.

PM0350-01 MEGATOUCH™ TITANIUM 2 EDITION KIT 7

Status

Light

This is the last step for programming a tournament
sequence.
Status can be toggled to RUNNING , DELAYED or

STOPPED by touching the associated traffic light

color.   RUNNING  (green) means the current
tournament will start upon returning to the Game Menu
Screen;  DELAYED  (yellow) means the current
tournament will start at the programmed time and date.
The tournament settings are  LOCKED  (red) for the
current tournament after credits have been played for
that tournament. WHEN THE STATUS IS  LOCKED,
ANY CHANGES TO THESE FIELDS WILL AFFECT
THE NEXT TOURNAMENT (S) ONLY.

Tournament

Duration

Sets duration for tournament games in the displayed
Tournament Sequence.

Prize Mode

Sets to POINTS or CASH, depending on tournament
type. When set to CASH, a message is displayed
reminding the user to confirm the legality of cash
tournaments in their area.

Prize

Pool

Sets the percentage of the tournament s total coin
drop to be used for tournament prizes.

Prize Pool

Starts At

Allows the operator to start the tournament with
cash/points already in the Prize Pool. The pool
increases as players deposit coins.

EXIT

Exits to the Tournament Controls screen. While in the
Tournament set up screen, highlighting any game in
the sequence, will turn this button to a cancel button
and will allow you to cancel out of the selected game
and restart your selection(s) for tournament play.

Operator

Set PIN

Displays the Set Attendant PIN keypad. The operator
can set up to four PINs to be used by attendants for
awarding prizes.

End Current

Game

Ends the current tournament game for the highlighted
sequence only.

Time and

Date

Fields

Touch the field you want to change and adjust the
value using the UP and DOWN arrows. Double-check
the time before performing Step 4. You cannot set the
time earlier than the current time. Tournament play
can be set in ten-minute increments past the real
time .

8 MEGATOUCH™ TITANIUM 2 EDITION KIT PM0350-01

FIGURE 8 – WINNERS’ SCREEN

Awarding Prizes

Players qualify for prizes by finishing with one of the top three high scores for the

tournament.

To award a prize, access the Winners’ List (by touching the screen in the idle mode

and then selecting the CLAIM PRIZES icon, or by entering the tournament game

selection screen and selecting LAST WINNERS.) Touch the CHANGE GAME icon to

locate the Winners’ List for the desired tournament (use the UP and DOWN arrows

to page through the list of winners).

On the Winners’ List Screen, touch the players’ name to whom the prize will be

awarded.

When the PIN keypad is displayed, an attendant must enter one of the four, pre-

programmed attendant PINs (see Figure 8).

The player then enters their PIN to confirm the awarding of the prize.

The attendant must then touch the PRIZE AWARDED icon to register the payout.

(NOTE: TOUCHING “EXIT”, WITHOUT TOUCHING “PRIZE AWARDED,” WILL

CAUSE THE PRIZE AWARD SEQUENCE TO BE ABORTED. THE SEQUENCE

WILL HAVE TO BE REPEATED TO AWARD THE PRIZE).

Pay Without PIN

If a player should forget their PIN, the attendant can press the SETUP button in place

of entering the player’s PIN. The sequence will continue as though the PIN had been

entered. Touch PRIZE AWARDED to register the payout.

PM0350-01 MEGATOUCH™ TITANIUM 2 EDITION KIT 9

Merit Industries, Inc. Software License Agreement

Merit Industries, Inc. ("Licensor") is willing to license the enclosed software to you only if
you accept all of the terms in this license agreement.

Ownership of the Software

The enclosed Megatouch™ software program ("Software") and the accompanying
written materials are owned by Licensor and are protected by United States copyright
laws, by laws of other nations, and by international treaties.

Restrictions on Use and Transfer

If this Software package contains multiple media types (such as CD's, flash cards,
hard drives, etc), then you may use only the type of media appropriate for your
Machine. You may not use the other media types on another Machine, or transfer, or
assign them to another user except as part of the permanent transfer of the Software
and all written materials (as provided for below in paragraph 4).

You may make one copy of the software for backup purpose only. You may not copy
or make backup copies of any software security key or software security device
under any circumstances.

You may permanently transfer the right to use the Software and accompanying written
materials (including the most recent update and all prior versions) if you retain no
copies and the transferee agrees to be bound by the terms of this Agreement. Such a
transfer of this license to another party terminates your license. You may not other-
wise transfer or assign the right to use the Software, except as stated in this para-
graph.

You may not operate or allow the operation of the Software at locations where the
operation of such Software does not comply with all local, state, and other governmen-
tal body laws and regulations.

You may not modify, adapt, translate, reverse engineer, decompile, disassemble the
Software or create derivative works from the Software or any component thereof; nor
may you remove, modify or hide or otherwise make unreadable or non-viewable any
notice, legend, advice, watermark or other designation contained on the Software,
component thereof, or output therefrom.

You agree that the Software and the authorship, systems, ideas, methods of opera-
tion, documentation and other information contained therein, and all versions, modifica-
tions and adaptations thereto are proprietary intellectual properties of Licensor and are
protected by civil and criminal law, and by the law of copyright, trade secret, trademark
and patent of the United States and other countries.

Limited Warranty

Licensor warrants, solely for your benefit, that the Software will function in material
conformity, with its accompanying documentation for a period outlined in Licensor's
standard product warranty period after your receipt of the Software.

Licensor's Obligations Under Warranty

Licensor's sole obligation under the aforesaid warranty shall be to utilize commercially
reasonable efforts to correct or modify such portion of the Software as to make it
materially conform with the applicable documentation.

10 MEGATOUCH™ TITANIUM 2 EDITION KIT PM0350-01

Grant Of License

10. Licensor grants to you the right to use one copy of the Software on a single Megatouch™

("Machine") accompanied by a single licensor factory authorized security key. Licen-
sor reserves the right to update versions of the software and the content to the
Machine as deemed appropriate by the Licensor.

Disclaimers

11.

EXCEPT AS PROVIDED IN THE SECTION ENTITLED "LIMITED WARRANTY", LICENSOR
MAKES NO OTHER PROMISES, REPRESENTATIONS OR WARRANTIES, WHETHER EX-
PRESSED OR IMPLIED, REGARDING OR RELATING TO THE SOFTWARE OR CONTENT
THEREIN OR TO ANY OTHER MATERIAL FURNISHED OR PROVIDED TO YOU PURSU-
ANT TO THIS AGREEMENT OR OTHERWISE AND LICENSOR SPECIFICALLY DISCLAIMS
ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE WITH RESPECT TO SAID MATERIALS OR THE USE THEREOF. TO THE MAXI-
MUM EXTENT ALLOWABLE BY LAW THE UNIFORM COMMERCIAL CODE OR OTHER
UNIFORM LAWS SHALL NOT APPLY TO THIS AGREEMENT.

Limitation on Liability

12. IN NO EVENT SHALL LICENSOR BE LIABLE UNDER ANY CLAIM, DEMAND OR ACTION

ARISING OUT OF OR RELATING TO THE SOFTWARE, OR LICENSOR'S PERFORMANCE
OR LACK THEREOF UNDER THIS AGREEMENT FOR ANY SPECIAL, INDIRECT, INCIDEN-
TAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES, WHETHER OR NOT LICENSOR
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH CLAIM, DEMAND OR ACTION. IN
ADDITION, WITHOUT LIMITING THE FOREGOING, IN ALL EVENTS THE REMEDIES AVAIL-
ABLE TO YOU SHALL BE LIMITED TO THE AMOUNT PAID BY YOU TO LICENSOR FOR
THE SOFTWARE.

13. IN NO EVENT WILL LICENSOR BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY

LOSS OF PROFITS, LOST SAVINGS, OR OTHER INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF YOUR USE OR INABILITY TO USE THE SOFTWARE.

General

14. The validity and construction of this Agreement and of the rights and obligations herein

shall be determined and governed by the laws of the Commonwealth of Pennsylvania,
USA. Any controversy or claim arising out of or relating to this agreement shall be
resolved in the appropriate venue in Pennsylvania, USA.

15. Merit, in its sole discretion, may assign this agreement or any of its rights and obliga-

tions hereunder.

16. If you have any questions concerning this Agreement or wish to contact Licensor for

any reason, please write: Merit Industries, Inc., 2525 State Road, Bensalem, PA 19020,
USA.

PM0350-01 MEGATOUCH™ TITANIUM 2 EDITION KIT 11

Contrat de licence de logiciel de Merit Industries, Inc.

Merit Industries, Inc. (ci-après le "Concédant") est disposé à vous accorder la licence
d'utilisation du logiciel ci-inclus, à condition que vous vous engagiez à respecter tous les
termes, clauses et conditions du présent contrat de licence.

Droit de Propriété

Le logiciel Megatouch™ (ci-après le "logiciel") et toute la documentation écrite, restent
la propriété du Concédant et sont protégés par les lois du copywright des Etats-Unis,
ainsi que par les lois des autres pays et les traités internationaux.

Restriction d'Utilisation et Transfert

Si le présent logiciel comprend plusieurs types de composants (tels que CD-ROM,
cartes flash, disques durs, etc), vous ne pouvez utilisez que ceux qui conviennent à
votre appareil. Il est strictement interdit de les utiliser sur un autre appareil, les transférer
-ou les céder à un autre utilisateur, sauf si en cas de transfert permanent du logiciel et
de toute la documentation écrite (comme indiqué ci-dessous au paragraphe 4).

Il est interdit de copier le logiciel, à l'exception d'une copie de sauvegarde. Il est aussi
interdit de reproduire -ou faire des copies de sauvegarde des programmes de clé de
sécurité ou autres fichiers de sécurité, quelles que soient les circonstances.

Vous pouvez céder en permanence à un tiers -le droit d'utiliser le LOGICIEL et toute la
documentation écrite l'accompagnant, (ainsi que la plus récente mise-à-jour et toutes
autres anciennes versions) seulement si vous n'en gardez pas de copies, et si le
cessionnaire s'engage à respecter les termes, clauses et conditions du présent Contrat.
Cette cession à un tiers met fin à votre licence. Autrement, vous n'avez pas la
permission de transférer ou d'accorder à un tiers le droit d'utiliser le présent logiciel,
excepté que tel que décrit dans le présent paragraphe.

Il est interdit d'utiliser le présent logiciel ou de permettre son utilisation dans des em-
placements où l'utilisation du présent logiciel n'est pas conforme aux lois et réglementations
locales, nationales ou réglementations d'autres organismes gouvernementaux.

Il est interdit de modifier, adapter, traduire, démonter, décompiler, désassembler le
logiciel ou créer du matériel dérivé du logiciel ou de tout composant de celui-ci; vous ne
pouvez pas enlever, modifier ou cacher ou rendre illisible ou non-visible toute instruc-
tion, légende, information ou filigrane ou autre désignation qui apparaît dans le logiciel,
composant dudit logiciel ou résultant dudit logiciel.

Vous convenez que le logiciel et les droits d'auteur, les systèmes, les idées, les
méthodes d'utilisation, la documentation et autre information incluse, ainsi que toutes
les versions, modifications et adaptations qui s'y rattachent sont les propriétés
intellectuelles du Concédant et sont protégées par le droit civil et pénal et par la loit sur
le copyright, le secret commercial, la marque déposée et le brevet aux Etats-Unis et
dans les autres pays du monde.

Limite de Garantie

Le Concédant garantit seulement à votre intention, que le logiciel permettra une utilisation
conforme, avec la documentation l'accompagnant, pendant la période temps indiquée
dans la période de garantie du produit standard du Concédant, à compter de la date de
livraison du logiciel.

12 MEGATOUCH™ TITANIUM 2 EDITION KIT PM0350-01

Responsabilité du Concédant aux termes de la Garantie

La seule obligation du Concédant aux termes de la garantie susmentionnée sera de
faire tous les efforts commercialement raisonnables pour corriger ou modifier la partie
du logiciel pour le rendre matériellement conforme aux spécifications de la documenta-
tion.

Concession de Licence

10. Le Concédant vous accorde le droit d'utiliser une seule copie sur un seul Megatouch™

(ci-après "Appareil") accompagné d'une seule clé de sécurité autorisée en usine et
fournie par le Concédant. Le Concédant réserve le droit de mise-à-jour des versions
du logiciel et du contenu de l'Appareil, quand il juge nécessaire de le faire.

Exclusion de toute autre garantie

11.

EXCEPTE COMME PREVU DANS LA SECTION INTITULEE "LIMITE DE GARANTIE", LE
CONCEDANT N'ASSURE AUCUNE AUTRE GARANTIE DE QUELQUE NATURE ET A
QUELQUE TITRE QUE CE SOIT, EXPLICITE OU IMPLICITE, EN RAPPORT AVEC LE LOGICIEL
ET LES COMPOSANTS QUI L'ACCOMPAGNENT OU, LE CAS ECHEANT, TOUT SUPPORT
OU MATERIEL FOURNI CONFORMEMENT AU PRESENT CONTRAT. EN PARTICULIER, LE
CONCEDANT NE PEUT DONNER AUCUNE GARANTIE, DE QUELQUE NATURE QUE CE
SOIT, POUR LA COMMERCIALISATION DE TOUS LES PRODUITS EN RAPPORT AVEC LE
LOGICIEL OU AVEC L'UTILISATION DE CELUI-CI. DANS LA MESURE OU CELA EST
PERMIS PAR LA LOI, LE CODE UNIFORME COMMERCIAL OU AUTRE LOI UNIFORME NE
S'APPLIQUE PAS AU PRESENT CONTRAT.

Limite de Responsabilité

12. LE CONCEDANT NE SERA EN AUCUN CAS RESPONSABLE DE TOUTE RECLAMATION,

DEMANDE OU ACTION RESULTANT DE OU EN RAPPORT AVEC LE LOGICIEL OU LA
PERFORMANCE OU MANQUE DE PERFORMANCE DU CONCEDANT EN VERTU DU
PRESENT CONTRAT POUR TOUS DOMMAGES D'UNE NATURE QUI N'EST PAS PRESUMEE
PAR LA LOI ET QUI DOIVENT ETRE EXPRESSEMENT PROUVES, DOMMAGE INDIRECTS,
DOMMAGES-INTERETS POUR PREJUDICE MORAL, QUE LE CONCEDANT AIT ETE AVISE
OU NON DE LA POSSIBILITE D'UNE TELLE RECLAMATION, DEMANDE OU ACTION. DE
PLUS, SANS LIMITER CE QUI PRECEDE, LES DEDOMMAGEMENTS A VOTRE DISPOSI-
TION SERONT LIMITES AU MONTANT QUE VOUS AUREZ PAYE AU CONCEDANT POUR
LE LOGICIEL.

13. LE CONCEDANT NE SERA EN AUCUN CAS RESPONSABLE DES DOMMAGES, Y

COMPRIS TOUTE PERTE DE PROFIT, PERTES D'ECONOMIE OU TOUS AUTRES
DOMMAGES INDIRECTS OU DOMMAGES-INTERETS ACCESSOIRES DECOULANT DE
L'UTILISATION OU DE L'IMPOSSIBILITE D'UTILISATION DU LOGICIEL.

Dispositions Générales

14. La validité et la construction du présent Contrat et les droits et obligations ci-inclus

seront déterminés et régis par les lois du Commonwealth de Pennsylvanie aux États-
Unis. Toutes litiges ou réclamations résultant ou relatives au présent Contrat feront
l'objet d'une procédure de conciliation dans un établissement compétent en Pennsylvanie,
aux Etats-Unis.

15. Merit Industries -réserve le droit de transférer le présent contrat à un tiers ainsi que ses

droits et obligations ci-après.

16. Pour toutes questions concernant le présent Contrat -ou si vous désirez contacter le

Concédant pour une raison quelconque, veuillez écrire à: Merit Industries, Inc., 2525
State Road, Bensalem, PA 19020, Etats-Unis.

PM0350-01 MEGATOUCH™ TITANIUM 2 EDITION KIT 13

Merit Industries, Inc. Softwarelizenzabkommen

Merit Industries, Inc. („Lizenzgeber") ist nur dann bereit Ihnen eine Lizenz für die beiliegende
Software zu erteilen, wenn Sie alle Bestimmungen dieses Lizenzabkommens akzeptieren.

Eigentumsvorbehalt der Software

Das beiliegende Megatouch™ Softwareprogramm („Software") und die schriftlichen
Unterlagen sind Eigentum des Lizenzgebers und sind durch die Gesetze der Vereinigten
Staaten und anderer Länder und durch internationale Verträge urheberrechtlich
geschützt.

Beschränkungen im Gebrauch und Transfer

Sollte diese Softwarelieferung mehrere Medien enthalten (z.B. CD, Karten, Festplatten
usw.), dürfen Sie nur die für Ihre Maschine angebrachte Medienart verwenden. Die
anderen Medienarten dürfen nicht auf anderen Maschinen verwendet werden oder an
Dritte übergeben werden, abgesehen von einem endgültigen Transfer der Software
und aller schriftlichen Unterlagen (wie im untenstehenden Paragraphen 4 beschrieben).

Sie dürfen nur eine Sicherungskopie der Software herstellen. Unter keinen Umständen
dürfen Sie einen Softwaresicherungsschlüssel oder Sicherungsmaßnahmen kopieren
oder davon Sicherungskopien herstellen.

Sie dürfen das Nutzungsrecht für die Software und die schriftlichen Unterlagen
(einschließlich der aktuellen Version und aller vorhergehenden Versionen) an Dritte
übertragen, wenn Sie keine Kopie behalten und wenn der Empfänger die Bestimmungen
dieses Abkommens akzeptiert. Bei einem solchen Transfer der Lizenz an Dritte erlischt
Ihre Lizenz. Abgesehen von den Bestimmungen dieses Paragraphen sind alle anderen
Transfers oder Übertragungen der Nutzungsrechte für diese Software unerlaubt.

Sie dürfen die Software nicht benutzen oder eine Nutzung gestatten, wenn eine
solche Nutzung der Software irgendwelche Gesetze und Verordnungen der
kommunalen oder staatlichen Behörden verletzen würde.

Es ist Ihnen nicht gestattet, die Software abzuändern, zu verändern, zu übersetzen,
rückumzuwandeln, zu dekompilieren oder zu zerlegen, oder aus der Software oder
eines Teils davon andere Werke abzuleiten. Sie dürfen auch aus der Software, einem
Bestandteil der Software oder aus den Datenausgaben der Software keine Hinweise,
Bemerkungen, Ratschläge, Wasserzeichen oder andere Markierungen entfernen,
verändern, verbergen oder auf andere Art unlesbar machen.

Sie akzeptieren, dass die Software und die Urheberschaft, die Systeme, die Ideen, die
Arbeitsweisen, die Dokumentation und alle anderen darin enthaltenen Informationen
und alle Versionen, Veränderungen, und Bearbeitungen davon das geistige Eigentum
des Lizenzgebers sind, und dass sie durch Straf- und Zivilgesetzgebung und durch
die Copyright-, Geschäftsgeheimnis-, Warenzeichen- und Patentgesetze der Vereinigten
Staaten und anderer Länder geschützt sind.

Beschränkte Garantie

Der Lizenzgeber garantiert zu Ihren Gunsten, dass die Software für die angegebene
normale Garantiezeit des Lizenzgebers nach Ihrer Annahme der Software in erheblicher
Übereinstimmung mit der beiliegenden Dokumentation laufen wird.

Verpflichtung des Lizenzgebers im Rahmen der Garantie

Die ausschließliche Pflicht des Lizenzgebers im Rahmen der vorstehenden Garantie
besteht darin, alle geschäftlich vertretbaren Schritte zu unternehmen, um Teile der
Software zu berichtigen oder abzuändern, bis sie mit der beiliegenden Dokumentation
erheblich übereinstimmen.

14 MEGATOUCH™ TITANIUM 2 EDITION KIT PM0350-01

Übertragung der Lizenz

10. Der Lizenzgeber gibt Ihnen das Anrecht, eine Kopie der Software auf einer einzelnen

Megatouch™ („Maschine") mit einem einzelnen werksmäßig gestatteten
Sicherungsschlüssel zu benutzen. Der Lizenzgeber behält sich das Recht vor, nach
eigenem Ermessen die Software und den Inhalt der Maschine zu verbessern.

Beschränkungen

11.

ABGESEHEN VON DEN BESTIMMUNGEN DES PARAGRAPHEN „BESCHRÄNKTE
GARANTIE" GIBT DER LIZENZGEBER KEINE SONSTIGEN VERSPRECHEN,
VERPFLICHTUNGEN ODER GARANTIEN, OB AUSDRÜCKLICH ODER STILLSCHWEIGEND,
FÜR DIE SOFTWARE ODER IHRE BESTANDTEILE ODER FÜR ALLE ANDEREN
MATERIALIEN, DIE IHNEN IM RAHMEN DIESES ABKOMMENS ZUR VERFÜGUNG
GESTELLT ODER ÜBERLASSEN WERDEN, UND DER LIZENZGEBER LEHNT
AUSDRÜCKLICH ALLE ANSPRÜCHE AUF MARKTFÄHIGKEIT UND EIGNUNG DER
BESAGTEN MATERIALIEN FÜR DEN GEWÖHNLICHEN GEBRAUCH AB. SOWEIT
GESETZESMÄSSIG ZUGELASSEN, SOLLEN DIE HANDELSRECHTLICHE
GESETZGEBUNG AUS DEM UNIFORM COMMERCIAL CODE ODER ANDERE GESETZE
AUF DIESES ABKOMMEN NICHT ANWENDBAR SEIN.

Haftungsbeschränkung

12. DER LIZENZGEBER HAT KEINERLEI HAFTUNG BEI EINEM ANSPRUCH, EINER

FORDERUNG ODER EINER KLAGE, DIE AUF NUTZUNG DER SOFTWARE, DER LEISTUNG
DES LIZENZGEBERS ODER DESSEN VERSAGEN IM RAHMEN DIESES ABKOMMENS
FÜR JEGLICHE FOLGE-, INDIREKTE, SONDER- ODER NEBENSCHÄDEN BERUHEN,
SELBST WENN DER LIZENZGEBER AUF DIE MÖGLICHKEIT EINES SOLCHEN
ANSPRUCHES, EINER FORDERUNG ODER EINER KLAGE HINGEWIESEN WURDE.
WEITERHIN UND OHNE BESCHRÄNKUNG DES LETZTEN SATZES, DÜRFEN IN ALLEN
FÄLLEN DIE IHNEN ZUR VERFÜGUNG STEHENDEN ABHILFEN DIE VON IHNEN FÜR DIE
SOFTWARE AN DEN LIZENZGEBER GEZAHLTE SUMME NICHT ÜBERSCHREITEN.

13. DER LIZENZGEBER HAT IN KEINEM FALL EINE HAFTUNG IHNEN GEGENÜBER FÜR

SCHÄDEN, EINSCHLIESSLICH ETWAIGER GEWINNVERLUSTE, NICHT REALISIERTER
EINSPARUNGEN ODER ANDERER NEBEN- ODER FOLGESCHÄDEN, DIE AUS IHRER
VERWENDUNG ODER GEBRAUCHSUNFÄHIGKEIT DER SOFTWARE ENTSTEHEN.

Allgemein

14. Die Rechtsgültigkeit und Provisionen dieses Abkommens und der darin enthaltenen

Rechte und Pflichten werden durch die Gesetze des Commonwealth of Pennsylva-
nia bestimmt. Alle Ansprüche, die aus diesem Abkommen entspringen oder dieses
Abkommen betreffen, werden am jeweiligen Verhandlungsort in Pennsylvania, USA,
verhandelt.

15. Merit kann nach eigenem Ermessen dieses Abkommen oder jedes der darin enthaltenen

Rechte und Pflichten an Dritte abtreten.

16. Bei Rückfragen über dieses Abkommen oder wenn Sie den Lizenzgeber aus einem

anderen Grund kontaktieren wollen, bitte schreiben an: Merit Industries, Inc., 2525
State Road, Bensalem, PA 19020, USA.

PM0350-01 MEGATOUCH™ TITANIUM 2 EDITION KIT 15

NOTES:

__________________________________________________________________

_______________________________________________________________

________________________________________________________________

___________________________________________________________________

_______________________________________________________________

________________________________________________________________

__________________________________________________________________

_________________________________________________________________

______________________________________________________________

________________________________________________________________

___________________________________________________________________

__________________________________________________________________

_________________________________________________________________

_____________________________________________________________________

___________________________________________________________________

__________________________________________________________________

___________________________________________________________________

__________________________________________________________________

________________________________________________________________

_________________________________________________________________