background image

COPYRIGHT © 2005 MERIT INDUSTRIES, INC.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

      Money Shoot

Monitor Removal

1. Turn off and unplug the game.

2. Unlock and open the top bezel

3. Use dental floss to carefully cut the foam tape holding the touchscreen to the monitor until

you are able to completely remove the screen.  Once the touchscreen is completely free
from the monitor, remove any residual foam tape from the monitor with denatured alcohol.
You will need to place the touchscreen on a stable surface until it is installed on the new
monitor.

4. Remove the 2 screws securing the monitor mounting bracket to the game.  See Figure 2.

5. Carefully shifting the monitor mounting bracket on the pegs (if necessary), remove the

following connections behind the monitor (see Figure 3):

VGA monitor connector (gray cord),

Power connector and ground screw,

Monitor control board connector,

Power cable connector (black and yellow wire).

6. Slide the monitor assembly off the bezel and put aside.

7. Unlock and open the monitor bezel.

8. If you will be reusing the existing touchscreen, remove the 2 screws fastening the

touchscreen controller to back of the monitor bezel (see Figure 1) and disconnect the cable
from the underside of the controller.  Locate and disconnect the Molex connector (orange
and gray wires).  See Figure 1.

If you will not be reusing the existing touchscreen, remove the cable clamps securing the
touchscreen cable and the touchscreen power harness.  Next, remove the screws fastening
the touchscreen controller (see Figure 6) to the game and disconnect the cable from the
underside of the controller.  Locate and disconnect the Molex connector (orange and gray
wires).  See Figure 1.

9. Return to the monitor assembly and remove the 4 corner screws securing the monitor to the

bracket.  See Figure 2.  Remove the monitor.

10.  Close and lock the monitor bezel.

manuals/manuals_manuals_Support_Center_7CMoney_20Shoot_7CMonitor_20Removal_20and_20Installation_pdf-html.html
background image

COPYRIGHT © 2005 MERIT INDUSTRIES, INC.

Monitor Installation

1. Attach the new monitor to the monitor mounting bracket with the 4 screws.

2.   If your replacement monitor already has a touchscreen, go to Step 3.

If you are using the original touchscreen, clean the glass on the new LCD monitor with the
supplied alcohol wipe, then cut pieces of the supplied ½” foam tape long enough to cover
each edge of the monitor without overlapping.  After the tape is in place on the monitor, peel
off the packing.  Carefully place the touchscreen over the monitor in the same manner it was
attached to the old monitor, making sure the screen is properly and evenly aligned over the
glass, then connect to the LCD panel.  Clean the front of the touchscreen with the supplied
alcohol wipe once it is in place.

3. Open the top bezel, then slide the monitor assembly onto the 4 pegs.  Reattach the 2

screws securing the monitor assembly to the monitor bezel.

4. Reconnect the following connections behind the monitor (see Figure 3).  Make sure to

preperly dress the wires so they remain secured.  Unlock and open the monitor bezel if
necessary:

VGA monitor connector (gray cord),

Power connector and ground screw,

Monitor control board wire connector, and

Power cable connector (black and yellow wire).

5.   If you are reusing the existing touchscreen, reconnect the touchscreen cable underneath the

touchscreen controller and secure the controller with the existing 2 screws.  Also connect
the Molex connector (orange and gray wires) to the main power harness.  Make sure to
preperly dress the wires so they remain secured. See Figure 1.

If you are not be reusing the existing touchscreen, install the new touchscreen controller with
the 2 screws.  Connect the molex connector, touchscreen controller cable, and the touchscreen
power harness.  Make sure to preperly dress the wires so they remain secured.  See Figure 1.

6. Close and lock the monitor and top bezels.

7. Plug in and turn on the game.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

Money Shoot (cont’d)

manuals/manuals_manuals_Support_Center_7CMoney_20Shoot_7CMonitor_20Removal_20and_20Installation_pdf-html.html
background image

COPYRIGHT © 2005 MERIT INDUSTRIES, INC.

FIGURE 1 - UNDERSIDE OF MONITOR BEZEL

SCREWS SECURING
TOUCHSCREEN CONTROL-

MOLEX CONNECTOR

POWER HARNESS

FIGURE 2 - MONITOR ASSEMBLY - TOP BEZEL OPEN

FOAM TAPE 
ADHESIVE

 

MONITOR PEGS (4) 

SCREWS SECURING MONITOR

TO MONITOR ASSEMBLY

(2 - 1 AT TOP NOT SHOWN)

4 SCREWS SECURING 
THE MONITOR TO THE 
MONITOR ASSEMBLY 

manuals/manuals_manuals_Support_Center_7CMoney_20Shoot_7CMonitor_20Removal_20and_20Installation_pdf-html.html
background image

COPYRIGHT © 2005 MERIT INDUSTRIES, INC.

FIGURE 3 - UNDERSIDE OF MONITOR ASSEMBLY

WIRES FOR REMOVAL
FROM MONITOR